What have you done to your mustang today?

[blk12gt]

9mpg? I thought mine was bad at 11.7.

Yep, I will post a pic later... 3 mile drive to and from work

Sent from my phone, spelling mistakes brought to you courtesy of tapatalk.

 

[07TGGT]

I was parked when I took that lol

 

[garner]

Cruised at 60-65MPH and got this...

I barely get 23 at 60

 

[blk12gt]

Speaking of MPG just filled vicky up for the second time and she beats the rustang too, 9.3 MPG

Sent from my phone, spelling mistakes brought to you courtesy of tapatalk.

 

[Redfireshaker06]

Kuplex, I like the rings. What did they cost you?

 

[claudermilk]

Got the front control arm replaced under warranty. No more old-car creaking over speed bumps. Now it's ready to get dropped.

 

[AnotherS197GT]

Bought 2011+ rotors, calipers, and brackets.

 

[GallopingFord]

Cruised at 60-65MPH and got this...

too many miles.

 

[LAStang1234]

Ryan does weigh in at 110lbs folks. Lol

Got majority of the D1SC put on.

Sent from my iPhone using Tapatalk while Moonwalking

 

[07TGGT]

147 actually lol.

Looks good brother!

 

[weather man]

Washed her up and got nasty road salt off. Took it for a spin and verified I do need drag radials. 4th gear I can get on and not boil the tires, but you are moving along then!

 

[Kuplex]

Kuplex, I like the rings. What did they cost you?

About $50 shipped off eBay. They are not direct fit though. They mostly clip in but I had to place a little bit of 3M on the top clip to keep it clipped in. They are slightly deeper than the 05-09 and that's where the problem is. There is also a small gap around the speaker vs inside the ring (the 2010+ must be slightly bigger). I solved this by placing a thin strip of black foam on the inside of the ring to fill it in.

 

[skwerl]

My boost gauge quit working because the vacuum line popped off the back of the intake manifold. So I got to remove the CAI, throttle body and blower elbow in order to get my fingers on it to push everything back together. Five months since installing the new motor and my tune still isn't right. I'm starting to run out of patience.

 

[Dubstep Shep]

I finally got my car running correctly after the new engine. No codes or check engine lights!

Now all I need is a tune.

 

[Doug M]

^^^Awesome...congrats!!

 

[o2sys]

Did another test fit:

 

[speedfreak1000]

hydro dipped my vents today. still need to wet sand and buff the clear coat.

 

[LAStang1234]

YOU hydrodipped them David?!

 

[speedfreak1000]

yeah. I still need to wet sand and buff the clear to give it a smoother look but it added a little something to the boring looking dash. gonna do a few more little parts later today. I did the steering wheel spokes, I posted a pic in the pimping thread under my steering wheel/ airbag cover thread.

did these too, they came out ok cause the car is a daily driver but I may redo them.





BTW im digging that D1SC. someday maybe i'll be able to afford to S/C this car.

 

[LAStang1234]

yeah. I still need to wet sand and buff the clear to give it a smoother look but it added a little something to the boring looking dash. gonna do a few more little parts later today. I did the steering wheel spokes, I posted a pic in the pimping thread under my steering wheel/ airbag cover thread.

did these too, they came out ok cause the car is a daily driver but I may redo them.

BTW im digging that D1SC. someday maybe i'll be able to afford to S/C this car.

Even if you can't afford it, just do it! Lol

How are you hydrodipping them yourself?