Parting out car.

[05yellowgt]

Ok guys, moving an entire car in this economy sucks so I am going to start making preparations to part the car out.

Short Block $3500
Teksid block 0.20 over
Kellog 3.75 stroker crank
Probe 4340 I-Beam rods
Custom CP pistons (9.3 compression)
ARP hardware throughout including head studs
Motor has ~1,500 on it currently and has supported 700rwhp through stock heads and cams. Dyno'd 315/350 n/a before the blower on a break in tune.


Blower $4700
Polished Procharger F1A 12 Rib kit complete. Comes with ATI Dampener, complete 12 rib kit. Comes with 4.30" and 5.25" pulleys. I don't know how much boost the 5.25" pulley made because it would not clear the hood so I bought the 4.3" The 4.3" makes 27psi@7000rpm on my particular combo. I'll also include an HPX mass air meter along with the blower.



Fuel system $1800
Fore Triple pump hat anodized black
3 GT Pumps
MDM Megadriver
#8 line
3-1 y block
Fore Billet Fuel rails anodized black
FRPP 80lb/hr injectors
This system has supported 700rwhp on E85 with some room to go on the fuel pumps. On race gas this same system will support well over 1000rwhp.

There are other parts (suspension, race seats, TR6060 & twin disc clutch) that I am on the fence on whether or not to put up for sale. Once I make a decision on those, I will post them up in this thread as well. I've tried to do a quick bit of research as far as what things have been selling for, I hope I'm in the ballpark. If not I can adjust accordingly. If by chance a buyer intends to purchase the entire car I may take this for sale thread down. Thank you in advance.

 

[StangPower05]

pm sent

 

[05stroker]

I'm sick !!!!! Hate to see this . Good luck , I would buy something but I think I have almost the same shit . If things seperate I would like a price on the HPX , Fuel rails, and 3-1 Y block.

 

[firestang70]

Bump for a friend. He is a top notch fella and everything is first rate quality.

 

[Grip]

What kind of dampers do you have?

 

[05yellowgt]

pm sent

Replied!

I'm sick !!!!! Hate to see this . Good luck , I would buy something but I think I have almost the same shit . If things seperate I would like a price on the HPX , Fuel rails, and 3-1 Y block.

Things may change, who knows. Right now my priorities just aren't cars. Having kids really changes ones perspective on things. I'll let you know if I can separate any of the fuel system parts.

Bump for a friend. He is a top notch fella and everything is first rate quality.

Thanks bud!

What kind of dampers do you have?

Do you mean the ATI Dampener that comes with the Procharger kit? If you mean shocks/struts, I don't have those for sale.

 

[Tre06GTP1SC]

I wish you took payments, I would love to upgrade to that blower setup. GLWS!

 

[BLKS197]

Ugh want your motor GLWS

 

[Bad500chris]

pm sent!

 

[beefcake]

bump,

i know ya been busy with them new baby's!

Lemme know on them seats brother!

 

[05yellowgt]

Everything above is back up for sale. Will be listing additional parts (race seats and possibly suspension parts). I am returning the car to stock or very close to it.

 

[ROUSH1711]

That is depressing,Ive followed this car a long time,always impressive. Good luck with the family,the toys will always be around.

You gotta love this quote though...

" I don't know how much boost the 5.25" pulley made because it would not clear the hood so I bought the 4.3" The 4.3" makes 27psi@7000rpm "


HAHA

 

[beefcake]

That is depressing,Ive followed this car a long time,always impressive. Good luck with the family,the toys will always be around.

You gotta love this quote though...

" I don't know how much boost the 5.25" pulley made because it would not clear the hood so I bought the 4.3" The 4.3" makes 27psi@7000rpm "


HAHA

lmao

 

[Hysteria]

What would you be asking for the TR6060 and the clutch?

 

[05yellowgt]

Clutch and trans is already pending sale. If it falls through I will let you know. it will come with Transmission, Pro 5.0 shifter, cross member, Spec Twin Disc clutch and flywheel, and Dynotech Driveshaft.

 

[calispecial08]

who was the motor built by?

 

[05yellowgt]

Motor was built by my local speed shop owner, Michael Bell of Dayton Performance.

 

[Boomer_Gooner]

What pinion flange were you using with the Dynotech? Stock 05+? Or SN-95 1330? If the tranny deal falls through, and depending on the flange used and if you are willing to separate the d/s I will be willing to buy it.

 

[calispecial08]

for this block i would need different motor mounts correct?

 

[05yellowgt]

What pinion flange were you using with the Dynotech? Stock 05+? Or SN-95 1330? If the tranny deal falls through, and depending on the flange used and if you are willing to separate the d/s I will be willing to buy it.

It uses the 05+ flange, but I am not planning on seperating the transmission components at this time.

for this block i would need different motor mounts correct?

The block does require motor mount adapters and they are to be included with the shortblock.