Installing a paxton novi 2200.

[Wicked97]

I am looking around for these and moat say they fit '05-09 but make no mention if they fit '10/11+. Just to confirm, yours does fit an '11+ one correct?

Sent from my DROIDX using Tapatalk 2

Yes we made it based of the 11+

 

[Wicked97]

While I don't have a canton piece sitting next to me. If you look in the picture the canton piece has all of its welds exposed for the bungs that are used to attached the tank to the bracket.

Ours however does not

Also the bead's on our welds are much more uniform and ours comes with all the required brackets to install one into a car that didn't already have the reservoir. Which works our really well for the TVS guys who want to upgrade

It holds roughly
74 Ounces of fluid



Ours comes with all the required hardware for people like you to swap it into their cars.

Im trying to get some better pictures of it in the car

 

[stang8psi]

So is this tank pretty much guaranteed to warp and anyone considering this should add the cost of a Canton?

thats what I did , I didn't even waste time on the paxton tank!

I have a brand new paxton/vortech tank if anyone wants a spare!

 

[konablue11gt]

I dont have one in my hands we are making more right now.

Our tank is the exact size of the paxton tank

Any chance you could make it narrower and longer vs the same size? Id love to use my custom 5.0 billet oil cap but the tank doesnt allow me any room and its tight near my strut tower brace as well . I know ..wishful thinking out loud

 

[gizmo5]

Any chance you could make it narrower and longer vs the same size? Id love to use my custom 5.0 billet oil cap but the tank doesnt allow me any room and its tight near my strut tower brace as well . I know ..wishful thinking out loud

Thats what I suggested in a PM. It would hands down be the better option if the cap was moved towards the front and not be in the way of the STB.

JPC, do this, and I will buy one.

 

[konablue11gt]

Thats what I suggested in a PM. It would hands down be the better option if the cap was moved towards the front and not be in the way of the STB.

JPC, do this, and I will buy one.

actually do that and i'll buy one as well. 2 inches narrower and cap moved to the front.

 

[Kenaizer]

Same here! I'd even pay a little more.

 

[stretch]

eric@jpc-where is your tank made ?

 

[gizmo5]

Boom sauce! See Eric, my idea works. lol

Put me on the payroll for design and engineering...

 

[Wnt2gofst]

I agree. Slimmer and cap moved I would buy one.

 

[konablue11gt]

Dam theres 5 of us off the get go. Im positive there are others here too. Make it happen JPC

 

[gizmo5]

Im about to go buy some aluminum sheets and a TIG and start knocking these out... lol JPC, make it happen or I will! And I'll patent that mofo! lolololol

 

[Bigmack2012Gb]

Count me in :0

 

[Wnt2gofst]

Im about to go buy some aluminum sheets and a TIG and start knocking these out... lol JPC, make it happen or I will! And I'll patent that mofo! lolololol

I'M willing to chip in on it all.

 

[Failborne]

Im Game for one as well

 

[stang8psi]

Yup, I'd be interested..

 

[Juiced 66]

Me too.. Since mine has a small leak.

 

[Juiced 66]

what pid are you logging when you're pegging the mass air? Because the 86.6lb/min limit is actually a limitation of the pid due to sae reasons and not the actual maf limit.

Or are you pegging the voltage?

From what I understand, it's the lb/min that is being maxed out.

 

[sharkbaits]

Just a couple pictures of it installed on a customer's car.

 

[Wnt2gofst]

Actually looks smaller then Canton piece.