The PIC WHORE CLUB!!! Knock before you Enter!!!

[stang281]

 

[ChrisGT]

Sweet heavenly mercy. Pardon me while I go change.

 

[KrisR]

My new whip. Was stock with 18" wheels 2 weeks ago. Now has SR springs, thespoilerstore spoiler, Brembo wheels obviously.

 

[Gabe]

New AMR wheels and new tires finally mounted/balanced:

New 14" rear rotors with new Hawk HPS pads:

 

[swedensky]

Man gabe that looks really good behind the 18s, mine leaves more to desire



And the fronts:

 

[Gabe]

Man gabe that looks really good behind the 18s, mine leaves more to desire



And the fronts:

Thanks, I hope to have the 15" GT500 fronts on sometime this summer too, and the rear wheels will be 20's, so the brakes will look smaller then, but I'm still happy I got them done. Having that much more swept area is only good.

 

[NickD87]

Man gabe that looks really good behind the
And the fronts:


How did you get them powdercoated or painted?
I am looking at ordering a new set from ford and getting them done in red. Do you have to tear them down? can you replace parts or do they have to be replaced?

 

[swedensky]

How did you get them powdercoated or painted?
I am looking at ordering a new set from ford and getting them done in red. Do you have to tear them down? can you replace parts or do they have to be replaced?

I had mine powdercoated (my four Pistons also). The six Pistons have to have the Pistons and seals and all removed before the oven, the four Pistons need to be opened and taped off inside.

 

[NickD87]

I had mine powdercoated (my four Pistons also). The six Pistons have to have the Pistons and seals and all removed before the oven, the four Pistons need to be opened and taped off inside.

I'm getting the 4 piston so I can still drin drag wheels, can you explain more about disassembly and masking?

 

[swedensky]

I'm getting the 4 piston so I can still drin drag wheels, can you explain more about disassembly and masking?

They are two halves bolted together. After you separate them you must (CAREFULLY) remove the Pistons and seals and boots. If you haven't done this before I found the easiest way is to put an air compressor to the valve and blow them out but I put a small block in the caliper to keep the piston from exiting completely.

Then when you powdercoat them you have to mask off all of the surfaces that will touch something else (back to back with the other half, where bolts are put in, etc) because the coating will be too thick if done wrong for the assembly to go back together.


Or if you like grabber blue you can just buy my four Pistons =)

 

[NickD87]

Thanks
Sorry I think the blue would clash with the red theme

 

[TenSpeed]

 

[Gabe]

LMAO !!!! ^^^^^^

 

[Mr302Coyote]

Drove it to Sonic to meet up with a few friends. Hasn't been driven since November. Oh how i missed it.

 

[alrefire]

You won't be able to see the new mods once they're installed, so I figured I'd show it off here

 

[marcspaz]

I love shiny parts. LOL

 

[Gabe]

You won't be able to see the new mods once they're installed, so I figured I'd show it off here
View attachment 52158

You're missing 2 of each

 

[cbass]

Sweet heavenly mercy. Pardon me while I go change.

I'd need to change too, but I already done pulled my pants all the way off.

 

[alrefire]

You're missing 2 of each

Actually, I've got an extra
They sent me 7 pistons for some reason

 

[Boaisy]

Cause a 3.7L means you have 3 banks of 7 cylinders. You are missing the other 14.