Wire Tuck Thread

[onehotpny]

Damn I like that. Any details on it? I'm sure the glove box is cut though

here's a little more.

 

[onehotpny]

 

[Foozeh]

If I ever do this on my car I would probably just do a wiper fluid delete like this guy did for the fuse box.

 

[onehotpny]

If I ever do this on my car I would probably just do a wiper fluid delete like this guy did for the fuse box.

First time i've ever seen it mounted in that location. looks interesting .. only problem is I like my wind shield washer fluid reservoir. without it can't clean the wind shield...

 

[W3bb3r04]

here's a little more.

Do you know what is pictured securing it in place?

 

[W3bb3r04]

If I ever do this on my car I would probably just do a wiper fluid delete like this guy did for the fuse box.

Another problem is that if you had to change a fuse on the side of the road you would have to pull in inner fender and wheel and all that to get to the fusebox.

 

[onehotpny]

Do you know what is pictured securing it in place?

looks like some heavy duty string or cord, maybe this picture will help. what I plan on doing when I do mine is make some brackets , drill the holes I need and pop rivet the brackets to the fuse box to secure it under the dash.

 

[LAStang1234]

Looks like 550 cord

 

[NotQuik]

Looks good

 

[FIGSTR]

I like this, only because I already removed my reservoir lol will have to try it out

 

[2BlownStangs]

this was an awesome write as everyone has mentioned. I should attempt this since I'm in the middle of the engine swap.

 

[W3bb3r04]

this was an awesome write as everyone has mentioned. I should attempt this since I'm in the middle of the engine swap.

Definitely!! Thats the easiest since everything is out of the way.

 

[onehotpny]

my partial wire tuck is done , I'll relocate the fuse box and PCM at a later time once I get some Canton tanks to replace the Vortech ones , until then it would be useless to do the relocation as you can't see any wire for all the braided lines and tanks hide it.Now i have to make a bracket to mount my catch can and figure where I'm going to place it..

 

[rojizostang]

here's mine. i was too lazy to do a "how to"

 

[W3bb3r04]

my partial wire tuck is done , I'll relocate the fuse box and PCM at a later time once I get some Canton tanks to replace the Vortech ones , until then it would be useless to do the relocation as you can't see any wire for all the braided lines and tanks hide it.Now i have to make a bracket to mount my catch can and figure where I'm going to place it..

Looks good man! Definitely a good start on it!

here's mine. i was too lazy to do a "how to"

Yours was one of the ones that made me want to do this initially! Looks great as always

 

[onehotpny]

here's mine. i was too lazy to do a "how to"

Nice....

 

[onehotpny]

Well finished up today, made a clamp for the catch can and got everything done,except I'll wait to finish the gauge wire up till after I get the tune done.

 

[onehotpny]

Looks good man! Definitely a good start on it!





Yours was one of the ones that made me want to do this initially! Looks great as always

Even when I relocate the PCM & fuse box , mine won't be nothing like this ,since the vortech charge cooler and all the braided lines take a good bit of room. I still like how it turned out so far.

 

[RunnerInTheNight]

Grrr... this thread isn't that old & most of the pictures aren't loading, I just hope its on my end. This is an awesome project, maybe one day when I have a garage I can work on this.

 

[onehotpny]

Close up of catch can ..