Search results for query: *

Hey yall, I took some steps from a previous guide and put together a new one. I must say this is a LOT easier than using a pac module and dealing with a bunch of wiring and programming. This is as plug and play as it gets. I know this says 05-10 all but this will work for year that came with...

Man go figure, I was just talking about this with someone else too. Gauge is not even 3 months old. This is my third one. For some unknown reason it got stuck in heat cycle today and when it finally gets out, it pegs full lean and rich and basically goes all over the place. I've tried my other...

Hey yall. I've had a lot of people interested in my build. This is mostly just going to be eye candy. All carbon fiber interior is real, no overlays or stickers, some pieces custom made by me. Air vents are out of a 2016 mx5. Slight modification required. Forged engine, parts all from Joey...

Hey yall. I've recently noticed a weird problem. I have a fore l2 return fuel system with a fc3 staged controller and hobbs switch. If I drive it, then shut it off for a few minutes, it didn't want to start. This has happened twice today. Just cranks but if I unplug the fc3 and plug it back in...

Hey everyone I have my new engine in, t56 waiting on fuel system install finish. Anyway, I'm having trouble wiring. My kit came with no instructions. I need to know what to wire to for the level sender, and what pumps go to where. They're both the same pumps so I don't think that matters. I'm...

Hey all. So I'm putting my new engine and trans in and I bought every sensor brand new from ford. However, the knock sensors they sent had two separate connectors while the harness has a single 4 pin connector. So, I ordered the right one from LMR. I got it today and the connector is correct but...

For those of you that have installed the fore l2 fuel system, with the fc3 staged controller and hobs pressure switch, I'm curious as to how you ran lines, and where you put your controller. I just want some ideas. I have a dual pump setup by the way. I'm assuming I take my current white wire...

Getting closer and closer to getting this build done. Engine is built, t56 magnum is here and much more. I want to know for those who have done it, your thoughts and opinions on some built rear ends. I hear true Trac is the way to go, with the upgraded axles and c clip eliminators. My t56...

Hey all, I think I'm sure I have everything I need but I just want to clarify. I have all the parts already and want to be sure. I'm swapping to a t56 magnum xl in my 08 gt with a built engine. I have a Manley 8 bolt crank, so naturally, I needed an 8 bolt flywheel and a 26 spline clutch to...

Someone posted here awhile ago the service manual for the torque specs for everything on the engine. I specifically need the torque specs for the vct solenoid housings. I cannot find it anymore I've searched many times here and on Google. Does someone have this? Sent from my SM-N986U using...

Hey guys I'm going with a fore l2 return fuel system. I'm using the dual pump version with TI F90000267 pumps, and staged controller and Honeywell pressure switch. Fore mentions that for 07-10, they require the gt500 level sender. Doesn't state what part number, etc ..Can't find info on here, or...

Hey all. I'm sure some of you are aware of my build so I'll spare the time. I'm using v10 delete plates and locked oem phasers with custom grind cams from Todd warren. When degreeing these cams I'm aware you need a solid lifter. I went with the Ford performance rocker and lash adjuster kit. I...

Hey everyone..my build is progressing much faster than I thought. I have a built forged block with a forged Manley 8 bolt crank je pistons 9.5:1 comp molnar rods boundary oil pump, Todd Warren custom cams, t56 magnum xl, and much more....question on balancers....which brand to go with and why...

Looking for a tr6060, cross member and one piece drive shaft. Sent from my SM-N986U using Tapatalk

I'm currently building another engine. I am doing v10 block off plates, phaser lockouts, and a whole bunch more but timing componentsis the focus here. Making this engine be able to withstand 1000+ HP. I have read multiple good and bad things about MMR but I would like to hear everyone's...

Looking to buy a used nemak block part number on block rf3l2e with nemak stamp. Can be used but MUST have stock bore. Im needing a second block AND heads for another engine build. Heads must be in good condition with good caps and good cam journals. I found a few used Long blocks for 850 shipped...

I really hate to ask this question but I cannot find the info anywhere anymore. I cannot, for the life of me remember what part number I used to upgrade my 08 gt to the 2010 gt altenator. I know that there are two different part numbers. One for automatic and one for manual. Mine is a manual...

I got the install all done and my no start issue figured out. Car runs great. Did a small pull in third gear from 2-4000 rpm and boost gauge maxed at 5psi. I checked for vacuum leaks with a smoke machine and found none. I do have a softer spring in the BPV because I have cams. I spoke with mike...

I just finished installing my kennebell 2.6l intercooled kit and I cannot get it to start. Lito sent me a base startup tune and it wants to fire but it won’t. It will sputter a little and that’s it. Lito said the fuel pressure was high. I checked for vacuum leaks with a smoke machine and found...

Short and simple. I have the stage 1 2.6L intercooled supercharger kit from Kennebell. Lito mentioned something about a bypass valve mod because I have cams. I have hotrod cams I know they aren’t very aggressive but I know vacuum Will fluctuate at idle and cruising conditions so I don’t want to...

I have a kenne bell stage 1 SC for my 08 mustang GT which is a full bolt on. Cams, longtubes , etc. just wish now that I never bought my jlt series 3 cai or ford racing intake manifold now..anyway..for those of you have installed the kenne bell supercharger what were some things you had to...

Hey everyone I've been trying to get in touch with lito for months now. We were going through data logs to fix the treturn to idle issues I've had. The last time I even got a revision was before December. Last reply I received was in Dec ber staying that he just got back and is going to play...

I apologize for the what may seem like monotonous info but I feel as if its important to mention... Lito and I have been battling a return to idle issues for quite some time. Before I go on a rant I suppose, I want to mention some things to get your minds flowing. I noticed this issue start to...

Hey everyone I have an 08 gt 5 speed and I would like to hear your opinions on trans fluids. I tried RP syncromesh (not impressed shit came out like water) redline mt-90 was okay then Mercon ATF which is eh. Was wondering if Redline MTL which is 75w80 will be good enough for the trans. I live in...

Does anyone know if there is supposed to be a trim panel underneath the dash by the pedals? Looks like there used to be one there but I'm not sure. Its never been there since I had the car.