Wicked97
forum member
Hey guys i wanted to share a project with you guys that has been in the works now for a few months.
Over the next couple weeks we are going to be building what we hope is a bottom 8 second true street car with AC and the whole 9 yards.
Here is the car:
The car came to us with the following
TVS Blower
Exhaust
BAP
ID1000s
JLT
and Some rear suspension
He has already run some Mid 10s on Slicks with the MT82
We are pretty much getting rid of everything that was on the car and starting from scratch.
The build started off with the intentions of building a very high powered stick shift car that he could roll race with and do the TX mile. since then it has progressed a little into more of a drag inspired build. We ditched the Stick in favor of an Auto and got a little more hard core with the suspension and supporting mods.
His goal is basically grudge race and street race this car in Oklahoma
The Parts we are going to be adding:
JPC turbo kit Modified with a Garrett GTX4202R (76/82)
Air to water Intercooler
AMS 1000 with Co2
MSD 2 step
Rossler Power Glide trans 1.80 1st gear
PTC converter
JPC 2400 HP Fuel System
ID1300 Injectors
TRZ Anti Roll bar
BMR Upper mount
JPC Upper
BMR K member
Built 8.8 with strange Parts 3.15 gears
CJ springs
We are also installing a complete engine this is going to be one of the baddest Coyote Engines we have ever done.
Its a New 13 Block
Darton Sleeves
RGR Support System
Oliver I beam Rods
Diamond Pistons With coatings
Stock Boss Crank
Coated Bearings
All ARP Bolts
With the heads we are going to hand finish them install Bronze guides, Stainless Manley Valves, Custom Springs, New Valve Job. As far as the Cams Go we are sticking close to the Boss Specs but using a billet core
Now on to some pictures for you guys
Over the next couple weeks we are going to be building what we hope is a bottom 8 second true street car with AC and the whole 9 yards.
Here is the car:
The car came to us with the following
TVS Blower
Exhaust
BAP
ID1000s
JLT
and Some rear suspension
He has already run some Mid 10s on Slicks with the MT82
We are pretty much getting rid of everything that was on the car and starting from scratch.
The build started off with the intentions of building a very high powered stick shift car that he could roll race with and do the TX mile. since then it has progressed a little into more of a drag inspired build. We ditched the Stick in favor of an Auto and got a little more hard core with the suspension and supporting mods.
His goal is basically grudge race and street race this car in Oklahoma
The Parts we are going to be adding:
JPC turbo kit Modified with a Garrett GTX4202R (76/82)
Air to water Intercooler
AMS 1000 with Co2
MSD 2 step
Rossler Power Glide trans 1.80 1st gear
PTC converter
JPC 2400 HP Fuel System
ID1300 Injectors
TRZ Anti Roll bar
BMR Upper mount
JPC Upper
BMR K member
Built 8.8 with strange Parts 3.15 gears
CJ springs
We are also installing a complete engine this is going to be one of the baddest Coyote Engines we have ever done.
Its a New 13 Block
Darton Sleeves
RGR Support System
Oliver I beam Rods
Diamond Pistons With coatings
Stock Boss Crank
Coated Bearings
All ARP Bolts
With the heads we are going to hand finish them install Bronze guides, Stainless Manley Valves, Custom Springs, New Valve Job. As far as the Cams Go we are sticking close to the Boss Specs but using a billet core
Now on to some pictures for you guys
