Post your best 1/4 MILE ETs here!

Status
Not open for further replies.

05yellowgt

Senior Member
Joined
Apr 9, 2007
Posts
2,456
Reaction score
5
Location
Dayton, OH
60' 1.74
330 4.87
1/8 7.87
mph 104.36
1/4 11.24
mph 129.6

I spun out of the hole and short shifted into 2nd on this run. More seat time, maybe some new DR's and more practice should net me a 10 second ET. Slicks would probably get me pretty well into the mid 10's maybe a bit better.
 

ZmanM3

The Evil One
Joined
Apr 6, 2007
Posts
21,617
Reaction score
210
Location
Jackson, NJ
60' 1.74
330 4.87
1/8 7.87
mph 104.36
1/4 11.24
mph 129.6

I spun out of the hole and short shifted into 2nd on this run. More seat time, maybe some new DR's and more practice should net me a 10 second ET. Slicks would probably get me pretty well into the mid 10's maybe a bit better.

Haha, that looks like a time I would have in a 700 HP car. I think at your power Slicks would be a necessity.
 

fin1

Member
Joined
Apr 11, 2007
Posts
468
Reaction score
0
Location
Pittsburgh, PA
The car has been dancing around 10.0x to 9.9x for the last few months. I bracket race it every weekend and can't dial in faster than 10.00 since I'm not legal below 10.00, so running 9.99 or faster is useless to me. On this run Redfire (Will) and I decided to leave after this run since UMTR was running an event and were came just to get a few hits. Since we didn't want to stay late for the next round, I never lifted.
 

Attachments

  • IMG_1.jpg
    IMG_1.jpg
    30 KB · Views: 26

pacettr

PJ Lover
Joined
Aug 20, 2008
Posts
3,417
Reaction score
14
Location
Yukon, OK
1) timeslip--if you don't have it, unless you have video, forget it. If you only have video, please provide the 60', 1/8-mi and 1000' incrementals
2) The following vehicle information:
- Cubic inch displacement (CID) of engine 302
- Type of transmission (by model number) 3650
- Size and Manufacturer of power adder, or N/A Saleen Series VI
- Pounds of Boost, of N2O shot (or both if applicable) 3.0 pulley (no gauge yet)
- Rear Gear ratio 3.73
- Make, type, and size of tire M&H Racemaster DR, 275/45-18
3) Post two slips from the same day---shouldn't be a problem as rarely do you go to the track and make only one pass.



60' - 1.834
330 - 4.932
1/8 - 7.47
MPH - 98.01
1000 - 9.636
1/4 - 11.477
MPH - 119.12



Also went 11.64, 11.53, 11.60
I'll try to scan in the slips tomorrow...
 
Last edited:

scramblr

Senior Member
Joined
Jun 27, 2007
Posts
4,812
Reaction score
136
Location
New Braunfels, Texas
Finally into the 11s!!!!!

Took long enough, but it was sweet. Number 949. Also note changes to set up:

298ci
M/T DRs 325/50 15
4:10 gears
12 PSI


picture.php

displayimage.php

displayimage.php
 
Last edited:

stkjock

---- Madmin ----
Staff member
Administrator
Super Moderator
Joined
Jul 10, 2007
Posts
40,524
Reaction score
3,334
Location
Long Island NY
60' - 1.834
330 - 4.932
1/8 - 7.47
MPH - 98.01
1000 - 9.636
1/4 - 11.477
MPH - 119.12



Also went 11.64, 11.53, 11.60
I'll try to scan in the slips tomorrow...

congrats man. what rims did you put the M&Hs on?
 

Redfire

Member
Joined
Apr 15, 2007
Posts
210
Reaction score
0
The car has been dancing around 10.0x to 9.9x for the last few months. I bracket race it every weekend and can't dial in faster than 10.00 since I'm not legal below 10.00, so running 9.99 or faster is useless to me. On this run Redfire (Will) and I decided to leave after this run since UMTR was running an event and were came just to get a few hits. Since we didn't want to stay late for the next round, I never lifted.

Congratulations Brad. Hopefully there will be a few weeks left.
 

psfracer

billy badass
Joined
Apr 6, 2007
Posts
10,917
Reaction score
82
Location
Valencia, CA
Everyone---please read the fist post in this thread if you wish to be added to the list---

If your information is not complete or you do not have the backup required, you will not be added to the list---as I like to think my list contains no bullshit.

If you don't have a scanner, take a picture of the timeslip and post it up---its not that hard.
http://s197forum.com/forum/showthread.php?t=5218
 
Status
Not open for further replies.

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top