Installing a paxton novi 2200.

[DSargent09]

Oh shit. Hope that's not why the car ran piss poor around the block the one time I tested it.

 

[beefcake]

the standard kit bolted on our 2014 just like any other car

 

[Mike Rousch]

Every 14 (including mine) i have seen come through the shop have all had 4 bolt pulleys as well.

 

[moostang09]

Using a kit from beefcake and id1000 injectors mine just made 672/574 on a mustang dyno using pump gas and stock exhaust manifolds jegs cat deletes and stock cat back

Can't go wrong

I used triangle speed shop

I've heard a lot of good things about Triangle! Out in Orange, Texas right?? I may go there when I get my kit one of these days.

Are you keeping the power that high it will you roll around on a more conservative tune?

Eventually I would like to be on a really safe tune and make around 600 to the wheels.

 

[DSargent09]

right is what comes on 2014s left is pulley that comes with kit.

Going off memory my car is 10/13 build date.

 

[konablue11gt]

did you call Vortech and ask em whats up?

 

[DSargent09]

Nope, wasn't very much of a size difference so I left stock one on. I tried to text beef, but didn't get a re.

You're right though I'll give them a call tomorrow.

 

[Greg Hazlett]

I thought it had to do with the number of ribs on the s/c belt?

 

[onebadgsx]

I thought it had to do with the number of ribs on the s/c belt?

He is just doinf the 6 rib. The kit still comes with a new pulley. Dont know why...

 

[Greg Hazlett]

Understand; when I was about to put the kit on my car I swapped over the WP pulley and the stock belt appeared to have one less or one more rib than the Paxton belt which is why the WP pulley needed to be swapped.

 

[DSargent09]

hmmm. I will definitely call paxton tomorrow, and if I dont get a re from them I will double check the ribs on the pulleys this weekend. Car is still sitting on ramps in the drive way. I have yet to cut and reinstall the lower splash shield just in case something needs attention.

 

[gremlinsteve]

I've heard a lot of good things about Triangle! Out in Orange, Texas right?? I may go there when I get my kit one of these days.

Are you keeping the power that high it will you roll around on a more conservative tune?

Eventually I would like to be on a really safe tune and make around 600 to the wheels.

That's the idea. The set to kill tune and a lighter tune. I plan on future mods and will have a beast mode tune also.
Just for show as i do not get to get to the tracks much

 

[gremlinsteve]

What size pulley? What other mods? Not afraid of going boom with that much power?

The pulley used was a 3.6 inch. I assume this is 10 psi correct?

 

[racksteris]

Every 14 (including mine) i have seen come through the shop have all had 4 bolt pulleys as well.

My 13 has a 4 bolt pulley..

 

[racksteris]

Using a kit from beefcake and id1000 injectors mine just made 672/574 on a mustang dyno using pump gas and stock exhaust manifolds jegs cat deletes and stock cat back

Can't go wrong

I used triangle speed shop

My Vortech GT/CS made 680/577..I'm running a 600 HP tune until motor is built.

 

[beefcake]

yep, give vortech / paxton a shout, they will get you the correct pulley

lemme know if you need anything

 

[Kenaizer]

The pulley used was a 3.6 inch. I assume this is 10 psi correct?

Depends. My 3.6 pulley actually made 13.5 psi. I'm still over 10 psi with the stock 3.8 pulley.

 

[Witt]

I have a 2014 with a 11/19/13 build date and have a 3 bolt water pump pulley as well. This might put the kibosh on my paxton with 8 rib plan. Any idea if they make a compatible 8 rib pulley?

 

[onebadgsx]

I have a 2014 with a 11/19/13 build date and have a 3 bolt water pump pulley as well. This might put the kibosh on my paxton with 8 rib plan. Any idea if they make a compatible 8 rib pulley?

Call them, also check with jpc.

 

[gremlinsteve]

Depends. My 3.6 pulley actually made 13.5 psi. I'm still over 10 psi with the stock 3.8 pulley.

I understand
This beast is supposed to be ten psi right now
I have other pullies that came with this kit too
Once I get oil pump gears and the fuel system I am going to swap over to corn and have TSS set it on kill