Search results for query: *

  1. redstangs9308gt

    5.0 Eforce owners

    So, I have my piggy bank and I am starting the collection of funds for another eforce kit. I had one on my 2008 mustang that was built and I was really happy with it. I have a f150 with the 5.0 and so far I can't find ANYONE who is running a f150 5.0 with a eforce. I used the search button and...
  2. redstangs9308gt

    x3 firmware issue

    I have a older x3 tuner that is being a problem. It is currently unlock and has 5 unlocks left. I am trying to update it so I can tune a newer car that isn't currently supported by the firmware installed on the x3 right now. I down loaded the newest sct device updater out. I installed the up to...
  3. redstangs9308gt

    How to obtain a complete 4.6 on the cheap?

    Guys I have never did this before, so all coments are welcome. Long story short I had to give up my 08 mustang and get a f150 to haul my family and projects around. I have a 93 mustang sitting out here that is good for nothin but a drag car which is where my heart is at anyways. I am really...
  4. redstangs9308gt

    Help with new ffrp axle and upper bushing install

    Ok, I purchased a new m-4001-svt373 axle. I am trying to figure out how to install this upper bushing(panhand brace). The bushing kit I purchased from late model restoration has too much play and doesn't have a metal sleave around it. Its part number is a53-01-05 My old rear end has the metal...
  5. redstangs9308gt

    8.8 issue, questions inside

    OK, I have searched the forums and I know I most likely have a pinion bearing or a crush sleave failure. But this is where my situation is different. My pinion flange has been leaking for a long time and just recently within the past 400 miles I have been feeling a vibration from the rear of the...
  6. redstangs9308gt

    WTB BBK X pipe for LT

    I am looking for a bbk x pipe used with bbk lt headers. Pipe can be catted or off road. If you don't have one but happen to stumble apon a good deal on one keep me in mind please. Thanks
  7. redstangs9308gt

    Comp 127350 Almost New

    ****Lower Price****** I have for sale comp 127350 cams. They are almost new with less than 60 miles on them. They are in perfect condition with little wear even showing on the lobes. The only reason why I removed them is I wanted more lift. Driveablity was perfect with these cams with a very...
  8. redstangs9308gt

    Well, Magnaflow 16674 3 inch it is

    So I finally purchased the Magnaflow kit 16674. Let me just say the stroker motor has never sounded so good. Deep throaty tone. Fitment was spot on. Very little adjustment was needed. Haven't drove it yet but will keep yall posted. For anyone wanting this kit, go for it. Mods are 302 stroker...
  9. redstangs9308gt

    Getting ready to order weld rims swaybar question

    Ok, so I am getting ready to order myself weld rims front and rear for christmas from a supporting vendor on here. (modifymystang) I want to run 10inch wide rims on the rear. My question/concern is that I already have CHE anti squat brackets on the rear and according to Che's website that the...
  10. redstangs9308gt

    Info about a website?

    Has anyone used or heard of this website www.nolimitspeed.com? Thinking about purchasing an item from them but with limited contact information just a little worried about spending that much money with them. I did send them a request for information and a person contacted me today with a gmail...
  11. redstangs9308gt

    3inch dynomax exhaust

    Ok, I have been shopping around for a good 3inch exhaust setup for my car. I was really wanting the magnaflow kit but I am not about to pay that much coin. So with that said, what do yall think about the dynomax 39460 kit? Oh and I should say that this will be used with a or/x so no doubt its...
  12. redstangs9308gt

    My new chatter vid inside

    Well, 127350s are in. I have great driveabilty. I upgraded to new metal tensioners with factory plastic guides. VCT is locked out. Both valve covers are quiet compared to my 127550 cams. But now I have a chatter/growl around the front cover. The sound is only present at idle and goes away...
  13. redstangs9308gt

    Where to buy a complete 8.8 custom built?

    Is there such a place where you can order a 8.8 to fit our cars custom built to your spec? I thought about going with a full 9 inch swap but I think that might require another driveshaft mod. I would like to get a new 8.8 built to have 3.90 gears with some upgraded posi unit type (air locker...
  14. redstangs9308gt

    Magnaflow 16674 Price request

    Venders please PM best price counting UPS ground shipping to 25621 Thank you NO FEDEX lol
  15. redstangs9308gt

    Priming /W front Cover off?

    Just wondering. Can you prime the engine so the tensioners will be expanded with the front timing chain cover off? Yees I searched this time lol.. I know I have been lazy today but with due rights.
  16. redstangs9308gt

    Timing pics

    I made this a new thread only for anyone else that might be searching and this will be a direct thread. Is my alignment correct? This is at the 6 oclock postion I made this one a large pic that way you can blow it up Don't know why these last two pics turned sideways
  17. redstangs9308gt

    cam swap wedge slipped

    well, its happend. I got the old cam out, bolted in the new cam, and while I was trying to get the phaser on the keyway of the new cam the chain slipped on the bottom. I have not touched the driver side cam yet so I know its still in time. WTF am I going to do about getting this car back in...
  18. redstangs9308gt

    Comp 127550 cams

    SOLD SOLD SOLD TO BRUCEH I have a set of comp 127550 blower cams for sale. $200 plus shipping. Let me warn you up front, nothing is wrong with the cams (less than 3000 miles on them with rev limiter set at 6700rpm) but if you are looking for driveabilty+lope cams you better buy yourself...
  19. redstangs9308gt

    Cam Tech plus 127350 lockout questions

    Ok, let me start out with does this look normal comp 127550 Ok, 2nd question has any one ran the 127350 cams lockout? Cause I am about too. What was the side effects?
  20. redstangs9308gt

    COMP 127550 owners come in here please

    With the comp 127550 cams, what is your vacuum@idle? Please include what your idle rpm is set too. I am getting ready to remove these cams. They are not adgreeing with my setup for some reason. The car will idle fine, BUT the idle has to be set above 925rpm not to have any stalling issues. This...
  21. redstangs9308gt

    Updated Heads compression tester

    Where can I purchase a compression tester that has everything included to do a compression test on a updated after feb of 2008 style head? Advance auto, autozone, napa or is this something I will have to purchase online? Part number or links would be great. Yes I searched.
  22. redstangs9308gt

    Need Fuel Pressure Reading Someone

    With the gt500 fuel pump kit, 60lbs injectors how much fuel pressure yall seeing on the fuel rail pressure sensor at idle? Mine is showing 38-40.
  23. redstangs9308gt

    How to Vacuum Smoke Machine (poor boy way)

    OK tomorrow I will take pics and you will have a better idea of everything. I used regular mineral oil & wd-40 to make thick smoke. I would disconnect the air hose going to the air compressure put a little amount of oil in the canister, hook the hose back up and turn the power on to the glow...
  24. redstangs9308gt

    ZERO Driveablity Sick of the BS

    Ok, I am sick of my car and its bull shit. I am thinking about trading it off and just being happy to get what I owe out of it. I don't understand how come I can't get this peice of shit to do idle recovery. All it knows is stalling out. Regardless of what pcv setup or lack there of I am...
  25. redstangs9308gt

    PCV help w/hose and coupling

    Ok, I have been using 5/8 soft radator hose on the driver side pcv. Well it keeps sucking itself together no matter how many different angles or routes or length. I even tried putting a pvc(water pipe) as a liner to make it not collapse. My car being the bitch it is did not like the restriction...

Latest posts

Support us!

Support Us - Become A Supporting Member Today!

Click Here For Details

Back
Top