What have you done to your mustang today?

[white95]

He’s on instagram…


Sent from my iPhone using Tapatalk

Whats his handle?

 

[UltraKla$$ic]

Yep!!


Sent from my iPhone using Tapatalk

Drove it to work

View attachment 82973

That garage…that car… sure does remind me of an old long lost friend of this forum, that lost his way.

I’d be speaking of the sterility of the place of course. You don’t happen to take your shoes off and where socks on your hands by any chance when you in there, do ya?


Sent from my iPhone using Tapatalk

Do you speak of Darren?

Yep!!


Sent from my iPhone using Tapatalk

 

[white95]

Bruh..

Just like Beetlejuice

 

[UltraKla$$ic]

Bruh..

Just like Beetlejuice

 

[stkjock]

jeeezz - what's it been 6 years ?

 

[UltraKla$$ic]

jeeezz - what's it been 6 years ?

At least! Miss me yet?

I was telling Josef that I've been visiting the idea of getting a clean 3V. I miss the ole s197.

 

[white95]

Yeah, you do.

 

[Mach2burnout]

Dang, and just like that…


Sent from my iPhone using Tapatalk

 

[Gabe]

That garage…that car… sure does remind me of an old long lost friend of this forum, that lost his way.

I’d be speaking of the sterility of the place of course. You don’t happen to take your shoes off and where socks on your hands by any chance when you in there, do ya?


Sent from my iPhone using Tapatalk

LMAO, my place is far from the shrine that Darren calls his garage.
Hell, I've got salamander in there every now and then!
I actually had to pull out the wife's Shelby and the riding mower to have the room to jack it up safely.
Yes, I think I need a bigger garage, haha.

It's usually much more crowded in there ...

 

[Mach2burnout]

At least! Miss me yet?

I was telling Josef that I've been visiting the idea of getting a clean 3V. I miss the ole s197.

What’s been going on bro?


Sent from my iPhone using Tapatalk

 

[BLKBULLITT]

Gave the car an oil change.

 

[GlassTop09]

Finally got around to getting the front end realigned this morning at my local Ford dealership after the FR M-3075-E FLCA kit installed some 3 yrs ago & OEM Bullitt springs installed a few months back (noticed that a 1/4" wide wear line appeared on the outer edge of the inner tread shoulder on both front tires.....indicating front end had excessive neg camber from the FR M-3075-E FLCA's (slightly longer from inner bushings center to center of ball joint than the '09 OEM units I replaced......will make note of this going forward for future references as I assumed that this length was std across the S197 chassis. I have the FR Caster\Camber bolts installed & had already marked cam alignments prior both installs so had set all back to alignment marks, so I figured all was in spec. Car drove fine so all was good.........NOT!). The tech told me that all else was good except camber was too far neg.......then I got chewed out for over tightening the cam bolts causing him to have to pull both front tires off & remove both calipers out the way to break them loose to set camber (so now I know my HF EarthQuake 1\2" Hi TQ Cordless Impact has no problem setting the 166+ ft-lb TQ spec for these bolts, which is what I used to tighten them then checked w\ my TQ wrench to ensure they met proper TQ specs.....hella easier than trying to get enough leverage using my TQ wrench while holding the cam bolt on alignment marks to tighten them. Yeah, I'm that well known there.)

Car now tracks straight as an arrow but is still very responsive to steering inputs so she's ready for the road now.

 

[GriffX]

Made a sheet from 3 mm ABS to fill the gap at the underbody on my 07 GT. Was more difficult than I thought. Have not done a high speed test yet, but no problems or noises so far.

 

[xeninworx]

Did brake swap all around yesterday. 4 piston Brembos and rear calipers powder coated Illusion Spanish Fly. In the shade it’s Bronze, in direct light it’s Gold. Matching Centric black hat rotors and 104 series brake pads all around. Eibach 5mm spacers all around. Boss 302 brake lines.

 

[DieHarder]

Purdy....so, did you take them apart; powdercoat and rebuild them yourself or buy it that way?

 

[xeninworx]

Purdy....so, did you take them apart; powdercoat and rebuild them yourself or buy it that way?

Yes, I took them apart. Sent them out to get powder coated and rebuilt them myself.

 

[Midlife Crises]

Yes, I took them apart. Sent them out to get powder coated and rebuilt them myself.

I like the rotors. They look heavy duty.

 

[redfirepearlgt]

Used to watch re-runs with my parents as a kid in the 80’s

Good times

I still watch it at 1030pm weeknights on METV

 

[xeninworx]

I like the rotors. They look heavy duty.

Thanks. The hats, inside and vents are coated black for protection. Winters here are salty.

 

[DieHarder]

Yes, I took them apart. Sent them out to get powder coated and rebuilt them myself.

Nice work.