What have you done to your mustang today?

[oldVOR]

I bet it made "a little bit of noise" before it even got to that point.

 

[XJCasper]

Recently did UPR hood pins and the Hurst short shifter.

Now trying to figure out my UPR catch can. Not fitting where it's supposed to go. Wondering if I got a wrong wrong mount bracket. Sucks I ordered this thing years ago. Will go back to UPR to ask questions. Ugh

 

[Mach2burnout]

My son picked up a cheap 06 GT. To say it needs some rear end work as an understatement. Looks like they lost a pinion bearing and then it all went downhill from there. Pretty heavily ground out pig casing


Sent from my iPhone using Tapatalk

Are you going to rebuild?

I have a 3:55 R&P that only has about 10k miles on it. I took it out of my 05 and packed it away. You’ll need a bearing kit.


Sent from my iPhone using Tapatalk

 

[Tman]

Are you going to rebuild?

I have a 3:55 R&P that only has about 10k miles on it. I took it out of my 05 and packed it away. You’ll need a bearing kit.


Sent from my iPhone using Tapatalk

Trying to buy a takeout rear axle assembly. Supposedly have one being shipped here locally today. Went to buy two separate axles nearby both of them turned out to be 7.5s not eight. 8.8.


Sent from my iPhone using Tapatalk

 

[XJCasper]

Collecting parts. Need my weekend to be here.

 

[Forty61]

Got my tie rods swapped out so while it was inside I cleaned the interior properly for a change.. still cleans up decent!

 

[redfirepearlgt]

Partial debadge today. Removed all the GTCS decals. Looks so much cleaner and sleeker.

 

[Forty61]

Partial debadge today. Removed all the GTCS decals. Looks so much cleaner and sleeker.

I’ve tossed around doing the same thing..

 

[oldVOR]

Partial debadge today. Removed all the GTCS decals. Looks so much cleaner and sleeker.

Any ghosting evident in the paint when you removed the decals after all these years?

 

[8sec_lx]

Cleaned and covered it.

 

[Joe combs]

Engine and trans swap, putting it back to the three pedal setup it left Ford as...Long tube headers and cat pipe, charge motion delete and underdrive pulleys, and powdercoated valve covers all going in during this install

 

[DieHarder]

Been chasing HE pump issues. Finally broke down so I bought a new 2013 HE pump for a GT-500; pulled the entire wiring harness that feeds it and replaced all of the connections; new high current power wire; cut and resoldered everything; shrink tubed everything; put it back together and bench tested it. Seems to run fine now. IAT's around 98 today for incoming air at the entry point to the blower and 123 compressed which is about right (about 20 - 23 deg temp difference for uncompressed vs compressed air) so will run it for the time being. Easy to tell if the HE pump is not working IAT's on the compressed side jump about 40 - 50 degrees compared to ambient.

 

[XJCasper]

Time to throw some new injectors in, and find out how bad ars Lito is.

 

[JEWC_Motorsports]

Ran it up to 135 mph

 

[Greg Hazlett]

Ran it up to 135 mph

Get the steering shake figure out?

 

[Gladams]

Installed BMR relocation brackets. Ride feels planted, and a bit smoother. Yes, it needs cleaned and painted. Will do that after upper control arm and bracket (BMR)

 

[WJBertrand]

Spray some Rustoleum Rust Reformer on those rusty bits, it’ll come out great.

Sent from my iPhone using Tapatalk Pro

 

[Gladams]

Spray some Rustoleum Rust Reformer on those rusty bits, it’ll come out great.

Sent from my iPhone using Tapatalk Pro

Will do. That looks good. Thanks.

 

[JEWC_Motorsports]

Get the steering shake figure out?

Yeah was lucky. Another thread here had same issue. Looked at hidden codes in forscan and cleared them. Drives perfect again.

 

[Gladams]

Installed new clutch reservoir.